Intech Power-Core Thermoplastics Engineering Blog

Intech Gears Could Eliminate Noise From Your Segway Gearbox

Posted by Alexander Bartosch on Jan 30, 2014 8:56:00 AM

Does your segway make too much noise? Have you ever wondered where it is coming from? Segway drive gears in the segway gear box are all metal (figure 1)

Segway Helical gear Gearbox

The metal on metal movement, in this beautifully constructed helical drive gearbox, creates noise. This noise can become worse with time as the gears wear.  See the video below for an example of the noise we are talking about.

Intech has conceptualized a segway replacement gear box to dampen vibration and reduce the noise of the segway metal on metal wear. Our simple bolt on attachment benefits from our  PA12GC Power-Core Cast Nylon (polyamide) which doesn't absorb moisture and won't crack in subzero conditions. The self-lubricating material allows our gears to run quietly and oil free. Removing another annoyance from the maintenance of your segway and its gearbox.

Using plastics to design high load, high shock, and highly critical applications is our specialty here at intech and being engineers the segway was always a toy we've wanted to tinker with. Making plastic gears for an application of this type was not without challenges. The first of which is the tooth root stress, you see metal gears can be much thinner and carry far more load than any plastic. The second is power transmission, very few - if any plastics can evenly and continuously transmit the power needed to drive a segway in the way its meant to operate. Imagine a right gear box transmitting less efficiently than the left and the circles or compensation a rider would need to make. Luckily, Intech's Power-core PA12GC material and its unique gravity casting process allows it to chemically bond to a metal core allowing it to transmit power evenly and continuously while perserving the benefit of a self lubricating gearing.

The retrofit is not inexpensive but if noise or vibration are causing you problems a new intech gearbox might be the solution to give you the quite and smooth riding personal movement device you've always wanted.

 Contact an Engineer

 

Photocredit: http://segwaynz.files.wordpress.com/2012/08/gearbox.jpg

Tags: Power-Core gears, cast nylon 12, gear box, gear backlash, gear design, plastic gears, Power Train Design, Plastic gear box, plastic helical gears

Moisture Absorption, Swelling in Nylons, except Cast Nylon Powercore

Posted by Simon Barrell on Nov 25, 2009 12:07:00 PM

Moisture absorption is a key factor to consider during nylon material selection. Design engineers need to take account of the application and tolerances because, machined component dimensions for a particular nylon grade will change if they were originally designed for a dry environment but are then used in a humid location. Moisture is absorbed by the part, and at some point when it reaches equilibrium, swelling can occur, and the fact that the dimensions of the part are subsequently altered increases the likelihood of premature part failure.

Injection molding, extrusion, and casting can all be used to form nylon, and the process used will influence material properties. In the case of injection molding, nylon is subjected to high compression and decompression within a short period of time. Correct mold design, timing, and precise pressure control are vital, and accurate thermal history for the part when both inside and outside of the mold should be maintained.

If water is present where extrusion is used in forming a part, severe problems can result. Therefore, moisture content and cooling rates should be monitored rigorously as they will both influence the physical properties of the extrusion.

Extruded rods or slabs can also be susceptible to shrinkage voids that are caused while the inside is in a molten state but the exterior surface begins to solidify. While the interior cools and shrinks under thermal contraction and crystallization, a void forms as the exterior no longer contracts. One solution is for extruders to use controlled water or vacuum quenching to cool formed parts. Note that even where forming processes can be precisely controlled, physical properties and dimensions may change over time when exposed to changing transport and storage conditions.  

Chart - Dimensional change polyamides versus moisture

The diagram shows moisture absorption causes swelling which results in up to 3.3% dimensional change in the nylon 6 family. When designing with nylon 6 or 6/6, this has to be taken into consideration, for example, when calculating backlash in gears, or when storing precision parts for prolonged periods of time in changing environments. For cast nylon powercore such change is negligible, even when permanently immersed in fuels, oils, and chemicals.

Tags: cast nylon 12, moisture absorption, calculating backlash, dimensional change, forming nylon, gear backlash, injection molding, material shrinkage, moisture content, polyamides